Click HERE for 360 View of the B3 cell
The Super B3 Complete Kit Sale. Everything you need, for a complete install, except water & electrolyte. Comes with a FS2 HHO-Edition Fuel Saver Electronic Circuit, and on dash digital ammeter & switch. Comes with downloadable instructions. Finally a break through, with the FS2, you don't need an EFIE, a O2 sensor circuit, a MAP/MAF adjuster circuit, just a OBD II car ( works on 1996 or newer cars) If you have a 87' to 95 year car, OBD I, we can supply you with a D-EFIE. Most model cars & trucks are available. See List Below. A "U-assemble kit. Install time about 4-8 hours. All electronics come pre-assembled, only few wires need assembling in place between yourt dashboard and engine compartment. Assembly photos and instructions are down-loadable. I would like to learn more about adding a hydrogen booster to my car.Water as a fuel? Read about the inventors and history of hydrogen.
Parts List
1) B3 Assembly (7 plates, screws & parts bag, cap, elbow 90º, top & bottom case, 2 terminals, 4 nuts, 4 washers)
2) Safety Bubbler/Spark Arrestor
3) PWM P30 ( pulse width modulator, in alum. case, as in photo.)
4) Hydroxy as Dryer, 1 micron filter/ spark arrestor.
5) 30 Amp Relay & wires.
6) ON/OFF dash baord switch
7) Digital Ammeter, small box with on/off switch.
8) FUSE link
9) Piggyback FUSE connector
10) FS2 HHO-Edition, Electronic Fuel Saver Circuit ( List your vehicle's make, model and year, below) 96'-2009 cars & trucks. If you have a 87' to 95' year car you have OBD I and FS2 will not work for you, soi we replace with a D-EFIE circuit.
11) Wire Kit - 8' of white & black 10 gauge wire, 4' of 22 gauge wire.
12) 6' of 3/8" ID reinforced poly clear hose.
The B3 Cell comes in black only.
The B3 Kit comes with the NEW FS2 HHO-Edition, Electronic Fuel Saver Circuitthat comes programmed with a highly tuned map and a set of EPROM addresses that directly affect fuel efficiency. When the ECU attempts to read the specific EPROM address, the FS2 circuit patches the factory value with one from its tuned map. It's exclusive patching algorithms to increase fuel efficiency across the map by up to 18%. The FS2 specifically changes values that affect fuel delivery and timing, based on readings from the MAP/MAF, IAT, and O2 sensors. Works along with your hydroxy gas generator.
Easy Installation, only 4 to 6 wires! Locate the OBD-II port, use the included connectors, or solder and you're done. Can still be used with your OBD II plugged in your excellant engine on board monitor : Scangauge II.
ATTENTION INTERNATIONAL CUSTOMERS : Please verify your vehicle is OBD-II compliant before making a purchase. 1996-2009 Cars and trucks are OBD II. Will not work with OBD I ( 1987-95) cars.
To order the right FS2 circuit for your make and model car or truck go tho this page : Make & Model and find your car in the list, copy and paste your car and model and then paste in the text box below. If your car is not in the list, then I'm sorry they don't make a circuit, yet for your car.
* Please note : These items are not stocked and are ordered, so allow one week extra for delivery of the FS2 circuit. We can ship the B3 Kit right away, but the circuit comes a week later. You will recieve 2 packages, with the B3 Kit. Also note the packing in the photo may come different, in black or a blue box. The box size is approx. is 1.5" x 1.5" x .5"
* This circuit is an "ehnancement circuit" and does not touch the ECM or change it's emission system, therefore making it legal for you to try it out and go green. Your emissions will be so clean from a good running HO booster, you will be able to pass any emission test with way cleaner emissions, hands down. Consult with your local SMOG man before testing, he may be for or against change. Terms & conditions of Hydrogen Junkie begin_of_the_skype_highlighting end_of_the_skype_highlighting